Elastomeric Roof Coating Green Français
Description
SEALFLEX Green elastomeric roof coating is a 100% acrylic water-based emulsion CR-4311 is specially formulated to cover and repair caravan and recreative vehicles roofs but also steel, wood, concrete, shingles and composite roofs. This waterproofing membrane reflects sun rays and to be U.V resistant and long-lasting. It resists to mildew, discoloration, cracking, peeling-off and chalking.
Surface Preparation
It is very important to clean all surfaces with a universal degreaser. To brush and rinse with plenty of water. Surfaces must be sound, clean and free from rust, loose paint, dust, dirt, grease and mildew. Clean with high pressure water. Scarify glossy areas. For holes and cracks we recommend Condor Sealflex colored plastic cement. Allow repairs to dry for 24 hours prior to apply SEALFLEX.
Application
Do not apply if rain or dew are forecast. Test on a small area to determine suitability of material.Avoid application under full sun. Do not apply over bituminous roofs. Do not dilute. Stir well before use. Temperature and relative humidity are critical factors for an adequate drying. For application and curing, we need to have 10ºC and a relative humidity less than 85%. Therefore ideal conditions are 25°C and 50% of relative humidity. Protect surface against rain until completely dried. Make sure roofs have slope to shed water. We recommend 2 to 3 coats to achieve a dry 0.76 mm (30mil or 1/32’’) thickness. Use a paintbrush, roller or industrial sprayer. When using paintbrush or roller, spread always in the same direction. Apply the second coat at right angle of the first one. Let dry between successive applications.
Cleanning
Clean tools with water while product is still fresh.
Package
Available in 3,78 L and 17 L pails.
Storage
KEEP FROM FREEZING.
Shelf Life
This product can be stored 1 year after purchasing date when kept in its tightly closed original container.
Technical Data Table
Specifications  
Color Green
Solid content 66 to 68 %
Density, shore A (ASTM D2240) 1,4 kg/L (about) (14 pmd/gal)
PH 8.5 to 9.5
Hardness, shore A (ASTM D2240) 40 for 21 days
Strength at rupture (ASTM D412) 350 PSI (2,41 MPA)
Tear Strength (ASTM D624) 49 PPI
Adhesion-in-Peel (ASTM C794) 40 PPI
Tensile Adhesion (ASTM C1135)  
25 % 75 PSI (0,52 MPA)
50 % 110 PSI (0,76 MPA)
100 % 140 PSI (0,97 MPS)
Adhesion to Rigid Substrates (ASTM D429) 1015,26 PSI (7 MPA)
Fragility at 40°C without rupture
V.O.C. content 250 g/L
Permeance to water (ASTM E96) Permeable
 

* Drying time depends on application method, temperature and porosity surfaces

Warranty
10 years limited warranty when installed and / or applied as recommended by the manufacturer. We will replace the product with a manufacturing defect. Under no circumstances will the manufacturer be liable for any amount in excess of the purchase price of the product used. The consumer must ensure that this product is suitable for the intended use. Because of atmospheric conditions, applicator competence and surface conditions being independent of the manufacturer's control, we limit our liability for one year following the date of purchase, with proof of purchase, to replacement of defective material only in its original hermetic container. Port paid factory (FAB factory).

Elastomeric Roof Coating
Elastomeric Roof Coating
Ecologic
Warning Simdut

MAY IRRITATE EYES AND SKIN. Do not get in eyes, on skin or on clothing. Keep out of reach of children.


FIRST AID TREATMENT: Contains Stoddard solvent. If swallowed, call a Poison Control Centre or doctor immediately. Do not induce vomiting. If in eyes, rinse with water for 15 minutes. If on skin, clean with mineral oil followed by soapy water then rinse well.
 
PDFdownload PDF version