Eagle Grout Non-Shrink Anchoring Grout Français
Eagle Grout is a one component, shrinkage-compensated rapid-set cementitious grout that allows very fluid consistency without any segregation. This grout is specially formulated to obtain very high strength. Ideal for interior or exterior applications with thickness that can vary from 12 mm (1/2”) to 60 mm (2 3/8”). Eagle Grout is formulated for structural grout for columns, machine bases, anchor bolts, base plates and soil stabilisation. It is free of chloride, gypsum and metallic aggregates.
Surface Preparation
Avoid working under intense sun. All surfaces shall be structurally sound, clean and free from traces of dust, oil, grease, paint, curing agent, coatings or exempt from any trace of acids, alkalis or any other material that can reduce adhesion. All concrete substrates shall be completely cured and at least 28 days old. They must be roughened to completely remove all traces of paint, coating, loosely bonded toppings. Use of Eagle Prime Plus as primer is a good alternative to concrete water saturation otherwise you may saturate concrete surface with clean water within few hours before repairs leaving no excess water and apply mortar when surface is dry again. Ambient, surface and product temperature must be superior than 10ºC (50ºF) and lower than 35ºC (95ºF) during the installation and for the first 72 hours. Some jobs may need the use of forms to hold ground, like column bases. Forms can be taken apart after a minimum of 3 days.
In a clean container, depending on desired consistency, pour 140 ml to 180 ml of fresh clean water per kilogram of product and gradually add Eagle Grout powder while mixing with a low-speed drill and a mixer. Blend for 2 to 3 minutes scraping recipient walls and paddle to obtain a homogeneous pourable lump-free consistency. Proceed immediately to application.
Eagle Grout takes 1 to 2 hours to dry depending on consistency. Drying may vary according to temperature and humidity level. Protect surface from rain, sun and wind. As soon as product starts to set, keep surface moisten with damp burlap, cover with plastic sheeting and allow a 72 hours curing.
Clean working tools and hands with water while product is still fresh.
This product is available in 5 kg pail and 22.7 kg bag.
Store in a dry and fresh area. Shelf life is 12 months in its original non-opened container.
Technical Data Table
Pot life     12 minutes
Set time initial / final ASTM C-191   45 minutes / 110 minutes 40 minutes / 60 minutes
Density ASTM C-185   2.08 kg/L 2.26 kg/L
Compressive strength ASTM C-109

24 hours
7 days
28 days

42 MPa (6092 PSI)
55 MPa (7977 PSI)
60 MPa (8702 PSI)
58 MPa (8412 PSI)
71 MPa (10 278 PSI)
84 MPa (12 183 PSI)
Flexural strength ASTM C-348 24 hours
7 days
28 days
8 MPa (1160 PSI)
8 MPa (1160 PSI)
8 MPa (1160 PSI)
9 MPa (1305 PSI)
10 MPa (1450 PSI)
11 MPa (1595 PSI)
Pull-out strength on concrete CSA A23.2-6B 7 days
28 days
2.1 MPa (304 PSI)
2.5 MPa (363 PSI)
3,00 MPa (435 PSI)
4,00 MPa (580 PSI)
 22.7 kg covers   0.01 m³ (0.36 ft³) 0.01 m³ (0.36 ft³)

* Drying Time depend

of surface porosity and temperature.

The customer shall verify of the suitability of this product for the intended purpose. Applicator's skill, weather and surface conditions being beyond manufacturer's control, we limit our liability to replacement of defective material only in sealed container, within 1 year of proof of purchase. FOB plant.

Eagle Grout
Eagle Grout
Avertissement Simdut Simdut

CORROSIVE: This product contains a cementitious blend and may cause eyes, skin and respiratory system irritation. When using this product: Wear safety glasses, gloves and a NIOSH approved anti-dust mask. Keep out of reach of children.

FIRST AID TREATEMENT: Skin contact: Wash with soap and water. Eye contact: Flush eyes immediately and abundantly with water for 15 minutes keeping eyelids opened. Consult a physician immediately. Ingestion: DO NOT INDUCE VOMITING. Give water if conscious. Keep victim warm and call immediately a physician.
PDFdownload PDF version