Eagle Polysab Polymer Sand For Paver Joints Français
Description
EAGLE POLYSAB is a mix of calibrated sand and latest generation high quality polymers. It is specially formulated to fill paver or slab joints on heavy traffic surfaces. Easy and ready-to-use, this mix is applied dry and hardens after wetting. This polymer-sand is formulated to stabilize paver surfaces by compensating dilatation movement either on areas like boardwalks, parking areas, decks, pool, etc. Being either horizontal or sloped surfaces, EAGLE POLYSAB stabilizes pavers and resists to erosion, water, freeze and thaw, cleaning, bad weeds and ants. It keeps paver joints filled, stable, durable, flexible and give excellent adhesion on more demanding jobs.
Surface Preparation
EAGLE POLYSAB has been formulated for joints of maximum width of 2.5 cm (1”). It must be used only if pavers or slabs have been installed over a drainage bed of sand or stone conform to trade practices. All surfaces shall be structurally sound, clean, dry and free from traces of oil, grease, wax or any material that can retain polymer at paver’s surface. They must also be exempt from any trace of acids, alkalis, chemical cleaning agent or any other material that can reduce adhesion. This product must be used by dry weather and without any risk of rain for a period of 24 hours. Ambient surface and product temperature must be superior than 10ºC (50ºF) during the installation and for the first 24 hours.
Application
Surface must be completely dry. Fill completely paver joints with a broom taking care to not sweep on long distances for product’s stability. Following paver manufacturer’s recommendations, use either a rubber hammer or a vibrating plate for packing or settling. Repeat these steps if necessary until joint is completely filled. Clean perfectly all residual dust from paving surface with a fine bristle broom and/or blower. Proceeding by 50 m² (500 ft²) section. Damp the surface with a fine mist so water won’t empty joints or remove some of the polymer-sand. Continuously moisten, without flood or water streaming, until joints are damp 4/5 in depth. Stop watering and proceed with next section. Let dry completely before exposing to humidity again. If there’s a risk of showers, protect from rain for a 24 hours period.
Mixing
Ready to use, no mixing is required. Proceed immediately with application and finishing.
Yield

Narrow joints : about 6 to 7 m² (65 to 75 ft²)
Wide joints : about 2 to 4 m² (21 to 43 ft²)
Nb.: The amount needed depends on the exact width of joint, the shape and size of the pad or slab.

Curing
Once dried, Eagle Polysab doesn’t need any restriction for pedestrian traffic, but it is preferable to wait 24 to 48 hours for car traffic. Curing time may vary according to temperature and humidity level.
Package
Available in 22.7 kg bag. Sand color.
Storage
Store in a dry and fresh area. Shelf life is 12 months in its original non-opened container.
Technical Data Table
CARACTERISTICS Eagle Polysab
Time delay before foot traffic 12 to 24 hours
Time delay before car traffic 24 to 48 hours
Warranty
The customer shall verify of the suitability of this product for the intended purpose. Applicator's skill, weather and surface conditions being beyond manufacturer's control, we limit our liability to replacement of defective material only in sealed container, within 1 year of proof of purchase. FOB plant.

Eagle Polysab
Eagle Polysab
Ecologic
Avertissement Simdut Simdut

CORROSIVE: This product contains a cementitious blend and may cause eyes, skin and respiratory system irritation. When using this product: Wear safety glasses, gloves and a NIOSH approved anti-dust mask. Keep out of reach of children.


FIRST AID TREATEMENT: Skin contact: Wash with soap and water. Eye contact: Flush eyes immediately and abundantly with water for 15 minutes keeping eyelids opened. Consult a physician immediately. Ingestion: DO NOT INDUCE VOMITING. Give water if conscious. Keep victim warm and call immediately a physician.
 
PDFdownload PDF version