Eagle Rapid Fix Rapid-Set Repair Mortar Français
Description
Eagle Rapid Fix is a one component polymer modified rapid-set cementitious mortar that allows quick repairs on old concrete imperfections at many thicknesses. This product is specially formulated to recondition old concrete, horizontally as well as vertically with thicknesses that can vary from 6 mm (1/4”) to 75 mm (3”) in one application. It can be used inside or outside.
Surface Preparation
All surfaces shall be structurally sound, clean and free from traces of dust, oil, grease, wax, paint, curing agent, coatings and loose particles, acids, alkalis or any other material that can reduce adhesion. All concrete substrates shall be completely cured and at least 28 days old. They must be roughened for a good adhesion and to remove completely all traces of paint, coating, loosely bonded toppings. Use of Eagle Prime Plus as primer is a good alternative to concrete water saturation. Otherwise, saturate concrete surface with clean water within few hours before repairs leaving no excess water and apply mortar when surface is dry again. Ambient, surface and product temperature must be superior than 10ºC (50ºF) and lower than 35ºC (95ºF) during installation and for the first 24 hours.
Application
Avoid working under intense sun.
Mixing
In a clean container, pour 170 ml of fresh clean water per kilogram of product. Add gradually Eagle RapidFix powder while mixing with a low-speed drill and a mixer. Blend for 1 to 2 minutes scraping recipient walls and paddle to obtain a homogeneous trowelable lump-free consistency. Proceed rapidly for application and finishing. Blend only quantities that can be applied in about 10 to 15 minutes.
Curing
Eagle Rapid Fix takes 15 to 35 minutes to dry. Curing time may vary according to temperature and humidity level. Protect surface from rain, sun and wind. Protect against weather, with a plastic sheeting in example, must be done without any contact with the surface. It could alter the finish. Wait from 2 to 3 hours prior to allow light traffic.
Cleanning
Clean working tools and hands with water while product is still fresh.
Package
This product is available in 5 kg and 15 kg.
Storage
Store in a dry and fresh area. Shelf life is 12 months in its original non-opened container.
Technical Data Table
CARACTERISTICS CURE EAGLE RAPID FIX (17% Water)
Pot life   12 minutes
Set time initial / final ASTM C-191   15 minutes / 35 minutes
Density ASTM C-185   1.88 kg/L
Compressive strength ASTM C-109

3 hours
24 hours
7 days
28 days

12 MPa (1740 PSI)
14 MPa (2030 PSI)
29 MPa (4206 PSI)
35 MPa (5076 PSI)
Flexural strength ASTM C-348 24 hours
7 days
28 days
6.5 MPa (943 PSI)
10.0 MPa (1450 PSI)
10.9 MPa (1580 PSI)
Pull-out strength on concrete CSA A23.2-6B 7 days
28 days
1.85 MPa (268 PSI)
2.13 MPa (309 PSI)
Coverage per kg of product   0.09 m² (1.0 ft²) for 6 mm (1/4”) thickness
 

* Drying Time depend of surface porosity and temperature.

Warranty
The customer shall verify of the suitability of this product for the intended purpose. Applicator's skill, weather and surface conditions being beyond manufacturer's control, we limit our liability to replacement of defective material only in sealed container, within 1 year of proof of purchase. FOB plant.

Eagle Rapid Fix
Eagle Rapid Fix
Ecologic
Avertissement Simdut Simdut

CORROSIVE: This product contains a cementitious blend and may cause eyes, skin and respiratory system irritation. When using this product: Wear safety glasses, gloves and a NIOSH approved anti-dust mask. Keep out of reach of children.


FIRST AID TREATEMENT: Skin contact: Wash with soap and water. Eye contact: Flush eyes immediately and abundantly with water for 15 minutes keeping eyelids opened. Consult a physician immediately. Ingestion: DO NOT INDUCE VOMITING. Give water if conscious. Keep victim warm and call immediately a physician.
 
PDFdownload PDF version