EAGLE TACKY CRETE Flexible Concrete Membrane Français
EAGLE TACKY CRETE is a polymer modified cementitious, with two components, specifically formulated to extend life of different materials. This high performance finishing product is flexible, environmentally friendly and affordable. You will protect and beautify your asphalt shingles,steel, wood, concrete, sandstone, stone or brick surfaces. It is available in several trendy colors. Easy to apply, in addition to being odorless and non-skid, it reduces the absorption of heat and help keep the roof and attic temperate. It has a high resistance at the cold, heat, UV rays, mildew, calcium, abrasive and acid rain. This is an excellent product to give a new life to your balcony, floor, foundation or roof.
Surface Preparation
It is important to prepare properly the surface to be covered. Clean the surface at a high water pressure with a universal degreaser or brush and rinse thoroughly with water. Surfaces must be cleaned, free from rust, peeled paint, dust, dirt, grease and mold. Scarify the surface for more adhesion. Holes, cracks and imperfections must be repaired before with the appropriate product. See the full Condor range repair products.
For the application and maturation of EAGLE TACKY CRETE, we need an ambient temperature above 10 °C and below 30 °C. Dilute the quantity that can be applied within 1 hour. After this time, the mixture should be changed because the setting reaction will be too late. To avoid rapid drying during hot season, protect from sun and wind. Avoid applying from direct sunlight. Protect from frost and rain during the 48 hours of application. In case of rain, protect the surface until completely dry. Apply EAGLE TACKY CRETE with a trowel, a brush , a broom brush or a stucco gun. You can also easily apply it with a specific roll sold at Condor Chimiques you only have to order it in the same time as your Tacky Crete. Spread the product in the horizontal direction for asphalt shingles or vertical direction on metal. If you whish you can apply with a roller expressively developed by Condor Beton to apply the Tacky Crete or Tacky Prestige. Two hours after the application of the Tacky Crete, apply two coats of Eagle Concrete Sealer to get a nice glossy finish to waterproof and ease the maintenance.
Dilute the quantity that can be applied within 1 hour. After this time, the mixture should be changed because the setting reaction will be too late. In a container, pour Part B (liquid). If you want to add color to the mix *, insert in Part B in order to get a nice even color. Then, gradually add Part A by mechanically mixing using a stirrer to obtain a homogeneous mixture. Let the mixture sit for 5 minutes then apply EAGLE TACKY CRETE. Never dilute the mixture with another liquid that is not sold with the product. In hot season it is best to mix only half a kit at a time to avoid the mixture to become too thick. *The color pigments are sold separately.

22.7 kg can cover up to 11.2 m2 (120 ft2) to a thickness of 3 mm (1/8’’). The coverage may vary depending on the application method, the skill of the applicator, porosity and surface condition.

Depending on the temperature and ambient humidity, allocate a drying time of at least 2 hours prior to the application of the sealant. The temperature and humidity are factors that influence drying time of the product.
Available in 11.34 kg and 22.7 kg
Keep this product from freezing. It can be kept in its original container, tightly closed, for 1 year from date of purchase.
Technical Data Table
Density ASTM C 185: 1,59 kg/1L
Dry Time*: 8.5 to 9.5
Dry Time*: 50% HR to 20°C
To the Touch*:

About 1 hour

Completely Dry* 2 hours
Pull-out strength on concrete: 7 days 1.80 MPA 261 PSI
CSA A23.2-6B 28 days 3.49 MPA 505 PSI
Service Temperature: - 40°C to 90°C (- 104° F to 194° F)
Application Temperature: minimum 10°C (50° F)
Chemical Resistance: Resistant acid or alkaline solutions, greases and solvents.
Permeability to water vapor (ASTME96): impermeable

* Drying Time depend of surface porosity and temperature.

Keep from freezing
Do not apply on a roof recovered with tar or gravel or needing major repairs. Do not do outside work if the temperature is uncertain for the next 48 hours. Keep from freezing. Maintain and use at temperatures between 10 °C and 30 °C. Dilute the quantity that can be applied within 1 hour. After this time, the mixture should be changed because the setting reaction will be too late.
The customer shall verify of the suitability of this product for the intended purpose. Applicator's skill, weather and surface conditions being beyond manufacturer's control, we limit our liability to replacement of defective material only in sealed container, within 1 year of proof of purchase. FOB plant.

New! Easy to install with a roller
New! Easy to install with a roller
Avertissement Simdut Simdut

CORROSIVE: This product contains a cementitious blend and may cause eyes, skin and respiratory system irritation. When using this product: Wear safety glasses, gloves and a NIOSH approved anti-dust mask. Keep out of reach of children.

FIRST AID TREATEMENT: Skin contact: Wash with soap and water. Eye contact: Flush eyes immediately and abundantly with water for 15 minutes keeping eyelids opened. Consult a physician immediately. Ingestion: DO NOT INDUCE VOMITING. Give water if conscious. Keep victim warm and call immediately a physician.
PDFdownload PDF version