Eagle Top Grey Concrete resurfacing and repair mortar Français
Description
Eagle Top is a polymer modified semi-rapid setting cementitious mortar to repair and resurface old concrete finishes. This mortar is specially formulated to recondition old concrete, horizontally as well as vertically with thickness that can vary from 1 mm (1/32”) to 25 mm (1”) in one application. It can also be used to level floors or making small slopes indoors or outdoors.
Surface Preparation
Avoid working under intense sun. All surfaces shall be structurally sound, clean and free from traces of dust, oil, grease, wax, paint, curing agent, coatings and loose particles, acids, alkalis or any other material that can reduce adhesion. All concrete substrates shall be completely cured and at least 28 days old. They must be roughened to assure a good bond. Use of Eagle Prime Plus as primer is a good alternative to concrete water saturation. Otherwise, you may saturate concrete surface with clean water within few hours before repairs leaving no excess water and apply mortar when surface is dry again. Ambient surface and product temperature must be superior than 10ºC (50ºF) and lower than 35ºC (95ºF) during the installation and for the first 24 hours.
Mixing
In a clean container, pour exactly 165 ml of fresh clean water per kilogram of product. Add gradually Eagle Top powder while mixing with a low-speed drill and a mixer. Blend for 1 to 2 minutes scraping recipient walls and paddle to obtain a homogeneous trowelable lump-free consistency. Slake for 5 minutes and mix again for 1 minute. Proceed with application and finishing.
Curing
Eagle Top takes 3 to 5 hours to dry. Curing time may vary according to temperature and humidity level. Protect surface from rain, sun and wind. Protecting job against weather, with a plastic sheeting in example, must be done without any contact with the surface as it could alter the finish. Wait from 16 to 24 hours prior to allow light traffic.
Cleanning
Clean working tools and hands with water while product is still fresh.
Package
This product is available in 5 kg pail and 22.7 kg bag.
Shelf Life
Store in a dry and fresh area. Shelf life is 12 months in its original non-opened container.
Technical Data Table
CARACTERISTICS CURE EAGLE TOP grey (16% Water)
Pot life   > 1 :00 hour
Set time initial / final ASTM C-191   2 :00 hours / 4 :00 hours
Density ASTM C-185   2.00 kg/L
Compressive strength ASTM C-109 24 hours
7 days
28 days
15 MPa (2175 PSI)
39 MPa (5656 PSI)
46 MPa (6672 PSI)
Flexural strength ASTM C-348 24 hours
7 days
28 days
3.5 MPa (507 PSI)
11.5 MPa (1668 PSI)
13.5 MPa (1958 PSI)
Pull-out strength on concrete CSA A23.2-6B 7 days
28 days
2.50 MPa (362 PSI)
2.50 MPa (362 PSI)
Coverage per kg of product   0.09 m² (0.95 ft²) for 6 mm (1/4”) thickness
 

* Drying Time depend of surface porosity and temperature.

Warranty
The customer shall verify of the suitability of this product for the intended purpose. Applicator's skill, weather and surface conditions being beyond manufacturer's control, we limit our liability to replacement of defective material only in sealed container, within 1 year of proof of purchase. FOB plant.

Eagle Top Grey
Eagle Top Grey
Avertissement Simdut Simdut

CORROSIVE: This product contains a cementitious blend and may cause eyes, skin and respiratory system irritation. When using this product: Wear safety glasses, gloves and a NIOSH approved anti-dust mask. Keep out of reach of children.


FIRST AID TREATEMENT: Skin contact: Wash with soap and water. Eye contact: Flush eyes immediately and abundantly with water for 15 minutes keeping eyelids opened. Consult a physician immediately. Ingestion: DO NOT INDUCE VOMITING. Give water if conscious. Keep victim warm and call immediately a physician.
 
PDFdownload PDF version